|
|
TC 2 |
Fasteners |
ISO 10684: 2004/Cor 1: 2008 |
Fasteners – Hot dip galvanized coatings – Technical Corrigendum 1 |
TC 6 |
Paper, board and pulps |
ISO 217:2008 |
Paper – Untrimmed sizes – Designation and tolerances for primary and supplementary ranges, and indication of machine direction |
TC 8 |
Ships and marine technology |
ISO/PAS 30003: 2008 |
Ships and marine technology – Ship recycling management systems – Requirements for bodies providing audit and certification of ship recycling management |
TC 22 |
Road vehicles |
ISO 6626‑3: 2008 |
Internal combustion engines – Piston rings – Part 3: Coil-spring-loaded oil control rings made of steel |
ISO 10605:2008 |
Road vehicles – Test methods for electrical disturbances from electrostatic discharge |
TC 24 |
Particle characterization including sieving |
ISO 9276‑3: 2008 |
Representation of results of particle size analysis – Part 3: Adjustment of an experimental curve to a reference model |
TC 29 |
Small tools |
ISO 6752:2008 |
Tools for pressing – Round punches with 60 degrees conical head and straight shank |
TC 34 |
Food products |
ISO 734‑2:2008 |
Oilseed meals – Determination of oil content – Part 2: Rapid extraction method |
ISO 8534:2008 |
Animal and vegetable fats and oils – Determination of water content – Karl Fischer method (pyridine free) |
ISO 13906:2008 |
Animal feeding stuffs – Determination of acid detergent fibre (ADF) and acid detergent lignin (ADL) contents |
ISO 21527‑1: 2008 |
Microbiology of food and animal feeding stuffs – Horizontal method for the enumeration of yeasts and moulds – Part 1: Colony count technique in products with water activity greater than 0,95 |
ISO 21527‑2: 2008 |
Microbiology of food and animal feeding stuffs – Horizontal method for the enumeration of yeasts and moulds – Part 2: Colony count technique in products with water activity less than or equal to 0,95 |
TC 38 |
Textiles |
ISO/TR 12116: 2008 |
Textiles – Methods of simulating colour change during actual wear by means of laboratory colour-fastness tests |
TC 41 |
Pulleys and belts (including veebelts) |
ISO 5293:2004/ Cor 1:2008 |
Conveyor belts – Determination of minimum transition distance on three idler rollers – Technical Corrigendum 1 |
TC 43 |
Acoustics |
ISO 3382‑2: 2008 |
Acoustics – Measurement of room acoustic parameters – Part 2: Reverberation time in ordinary rooms |
TC 44 |
Welding and allied processes |
ISO 24034: 2005/Amd 1: 2008 |
Welding consumables – Solid wires and rods for fusion welding of titanium and titanium alloys – Classification – Amendment 1: . |
TC 45 |
Rubber and rubber products |
ISO 24999:2008 |
Flexible cellular polymeric materials – Determination of fatigue by a constant- strain procedure |
TC 46 |
Information and documentation |
ISO 2709:2008 |
Information and documentation – Format for information exchange |
TC 51 |
Pallets for unit load method of materials handling |
ISO 12776:2008 |
Pallets – Slip sheets |
TC 54 |
Essential oils |
ISO 3525:2008 |
Oil of amyris (Amyris balsamifera L.) |
TC 59 |
Building construction |
ISO 15686‑5: 2008 |
Buildings and constructed assets – Service-life planning – Part 5: Life-cycle costing |
ISO 15686‑8: 2008 |
Buildings and constructed assets – Service-life planning – Part 8: Reference service life and service-life estimation |
TC 61 |
Plastics |
ISO 11357‑6: 2008 |
Plastics – Differential scanning calorimetry (DSC) – Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT) |
ISO 15270:2008 |
Plastics – Guidelines for the recovery and recycling of plastics waste |
TC 67 |
Materials, equipment and offshore structures for petroleum, petrochemical and natural gas industries |
ISO 10426‑6: 2008 |
Petroleum and natural gas industries – Cements and materials for well cementing – Part 6: Methods for determining the static gel strength of cement formulations |
ISO 13628‑11: 2007/Cor 1: 2008 |
Petroleum and natural gas industries – Design and operation of subsea production systems – Part 11: Flexible pipe systems for subsea and marine applications – Technical Corrigendum 1 |
ISO 13704: 2007/Cor 1: 2008 |
Petroleum, petrochemical and natural gas industries – Calculation of heater-tube thickness in petroleum refineries – Technical Corrigendum 1 |
ISO 28300:2008 |
Petroleum, petrochemical and natural gas industries – Venting of atmospheric and low-pressure storage tanks |
TC 68 |
Financial services |
ISO 4217:2008 |
Codes for the representation of currencies and funds |
TC 71 |
Concrete, reinforced concrete and pre-stressed concrete |
ISO 19338: 2007/Cor 1: 2008 |
Performance and assessment requirements for design standards on structural concrete – Technical Corrigendum 1 |
TC 84 |
Devices for administration of medicinal products and intravascular catheters |
TC 92 |
Fire safety |
ISO 5660‑4: 2008 |
Reaction-to-fire tests – Heat release, smoke production and mass loss rate – Part 4: Measurement of heat release for determination of low levels of combustibility |
ISO 16730:2008 |
Fire safety engineering – Assessment, verification and validation of calculation methods |
TC 98 |
Bases for design of structures |
ISO 13823:2008 |
General principles on the design of structures for durability |
TC 100 |
Chains and chain sprockets for power transmission and conveyors |
ISO 10190:2008 |
Motorcycle chains – Characteristics and test methods |
TC 106 |
Dentistry |
ISO 3823‑2: 2003/Amd 1: 2008 |
Dentistry – Rotary bur instruments – Part 2: Finishing burs – Amendment 1 |
ISO 11143:2008 |
Dentistry – Amalgam separators |
TC 107 |
Metallic and other inorganic coatings |
ISO 2080:2008 |
Metallic and other inorganic coatings – Surface treatment, metallic and other inorganic coatings – Vocabulary |
TC 110 |
Industrial trucks |
ISO 22915‑10: 2008 |
Industrial trucks – Verification of stability – Part 10: Additional stability test for trucks operating in the special condition of stacking with load laterally displaced by powered devices |
ISO 22915‑20: 2008 |
Industrial trucks – Verification of stability – Part 20: Additional stability test for trucks operating in the special condition of offset load, offset by utilization |
ISO 22915‑8: 2008 |
Industrial trucks – Verification of stability – Part 8: Additional stability test for trucks operating in the special condition of stacking with mast tilted forward and load elevated |
TC 117 |
Fans |
ISO 5801:2007/ Cor 1:2008 |
Industrial fans – Performance testing using standardized airways – Technical Corrigendum 1 |
TC 121 |
Anaesthetic and respiratory equipment |
ISO 5364:2008 |
Anaesthetic and respiratory equipment – Oropharyngeal airways |
ISO 9170‑1: 2008 |
Terminal units for medical gas pipeline systems – Part 1: Terminal units for use with compressed medical gases and vacuum |
ISO 9170‑2: 2008 |
Terminal units for medical gas pipeline systems – Part 2: Terminal units for anaesthetic gas scavenging systems |
ISO 15002:2008 |
Flow-metering devices for connection to terminal units of medical gas pipeline systems |
TC 126 |
Tobacco and tobacco products |
ISO 6488:2004/ Cor 1:2008 |
Tobacco and tobacco products – Determination of water content – Karl Fischer method – Technical Corrigendum 1 |
ISO 22303:2008 |
Tobacco – Determination of tobacco specific nitrosamines – Method using buffer extraction |
ISO/TS 22304: 2008 |
Tobacco - Determination of tobacco specific nitrosamines - Method using alkaline dichloromethane extraction |
TC 127 |
Earth-moving machinery |
ISO 2867:2006/ Cor 1:2008 |
Earth-moving machinery – Access systems – Technical Corrigendum 1 |
ISO 5006:2006/ Cor 1:2008 |
Earth-moving machinery – Operator's field of view – Test method and performance criteria – Technical Corrigendum 1 |
ISO 9244:2008 |
Earth-moving machinery – Machine safety labels – General principles |
ISO 16754:2008 |
Earth-moving machinery – Determination of average ground contact pressure for crawler machines |
TC 131 |
Fluid power systems |
ISO 3601‑1: 2008 |
Fluid power systems – O-rings – Part 1: Inside diameters, cross-sections, tolerances and designation codes |
ISO 3601‑2: 2008 |
Fluid power systems – O-rings – Part 2: Housing dimensions for general applications |
ISO 16889:2008 |
Hydraulic fluid power – Filters – Multi-pass method for evaluating filtration performance of a filter element |
TC 138 |
Plastics pipes, fittings and valves for the transport of fluids |
ISO 12176‑2: 2008 |
Plastics pipes and fittings – Equipment for fusion jointing polyethylene systems – Part 2: Electrofusion |
ISO 21003‑1: 2008 |
Multilayer piping systems for hot and cold water installations inside buildings – Part 1: General |
ISO 21003‑2: 2008 |
Multilayer piping systems for hot and cold water installations inside buildings – Part 2: Pipes |
ISO 21003‑3: 2008 |
Multilayer piping systems for hot and cold water installations inside buildings – Part 3: Fittings |
ISO 21003‑5: 2008 |
Multilayer piping systems for hot and cold water installations inside buildings – Part 5: Fitness for purpose of the system |
ISO/TS 21003‑7:2008 |
Multilayer piping systems for hot and cold water installations inside buildings – Part 7: Guidance for the assessment of conformity |
TC 145 |
Graphical symbols |
ISO 9186‑2: 2008 |
Graphical symbols – Test methods – Part 2: Method for testing perceptual quality |
ISO 20712‑1: 2008 |
Water safety signs and beach safety flags – Part 1: Specifications for water safety signs used in workplaces and public areas |
TC 146 |
Air quality |
ISO 16000‑15: 2008 |
Indoor air – Part 15: Sampling strategy for nitrogen dioxide (NO2) |
TC 159 |
Ergonomics |
ISO 11064‑5: 2008 |
Ergonomic design of control centres – Part 5: Displays and controls |
ISO 15743:2008 |
Ergonomics of the thermal environment – Cold workplaces – Risk assessment and management |
TC 160 |
Glass in building |
ISO 16293‑1: 2008 |
Glass in building – Basic soda lime silicate glass products – Part 1: Definitions and general physical and mechanical properties |
TC 163 |
Thermal performance and energy use in the built environment |
ISO 12241:2008 |
Thermal insulation for building equipment and industrial installations – Calculation rules |
ISO 12576‑2: 2008 |
Thermal insulation products – Conformity control systems – Part 2: In-situ products |
TC 164 |
Mechanical testing of metals |
ISO 7500‑1: 2004/Cor 1: 2008 |
Metallic materials – Verification of static uniaxial testing machines – Part 1: Tension/ compression testing machines – Verification and calibration of the force- measuring system – Technical Corrigendum 1 |
TC 171 |
Document management applications |
ISO 32000‑1: 2008 |
Document management – Portable document format – Part 1: PDF 1.7 |
TC 172 |
Optics and photonics |
ISO 9211‑3: 2008 |
Optics and photonics – Optical coatings – Part 3: Environmental durability |
ISO 24157:2008 |
Ophthalmic optics and instruments – Reporting aberrations of the human eye |
TC 173 |
Assistive products for persons with disability |
ISO 7176‑19: 2008 |
Wheelchairs – Part 19: Wheeled mobility devices for use as seats in motor vehicles |
TC 190 |
Soil quality |
ISO 17402:2008 |
Soil quality – Requirements and guidance for the selection and application of methods for the assessment of bioavailability of contaminants in soil and soil materials |
TC 193 |
Natural gas |
ISO 15970:2008 |
Natural gas – Measurement of properties – Volumetric properties: density, pressure, temperature and compression factor |
ISO/TR 26762: 2008 |
Natural gas – Upstream area – Allocation of gas and condensate |
TC 195 |
Building construction machinery and equipment |
ISO 19452: 2008/Cor 1: 2008 |
Building construction machinery and equipment – Pedestrian-controlled vibratory (percussion) rammers – Terminology and commercial specifications – Technical Corrigendum 1 |
ISO 21573‑2: 2008 |
Building construction machinery and equipment – Concrete pumps – Part 2: Procedure for examination of technical parameters |
ISO 21873‑1: 2008 |
Building construction machinery and equipment – Mobile crushers – Part 1: Terminology and commercial specifications |
TC 197 |
Hydrogen technologies |
ISO 22734‑1: 2008 |
Hydrogen generators using water electrolysis process – Part 1: Industrial and commercial applications |
TC 198 |
Sterilization of health care products |
ISO 13408‑1: 2008 |
Aseptic processing of health care products – Part 1: General requirements |
TC 210 |
Quality management and corresponding general aspects for medical devices |
ISO 15223‑1: 2007/Amd 1: 2008 |
Medical devices – Symbols to be used with medical device labels, labelling and information to be supplied – Part 1: General requirements – Amendment 1 |
TC 211 |
Geographic information/Geomatics |
ISO 6709:2008 |
Standard representation of geographic point location by coordinates |
TC 215 |
Health informatics |
ISO 27799:2008 |
Health informatics – Information security management in health using ISO/IEC 27002 |
TC 219 |
Floor coverings |
ISO 25620:2008 |
Laminate floor coverings – Determination of long-side friction for mechanically assembled panels |
CASCO |
Committee on conformity assessment |
ISO/PAS 17005: 2008 |
Conformity assessment – Use of management systems – Principles and requirements |
JTC 1 |
Information technology |
ISO/IEC 8824‑1: 2002/Amd 4: 2008 |
Information technology – Abstract Syntax Notation One (ASN.1): Specification of basic notation – Part 1: – Amendment 4: PER encoding instructions |
ISO/IEC 10646: 2003/Amd 4: 2008 |
Information technology – Universal Multiple-Octet Coded Character Set (UCS) – Amendment 4: Cham, Game Tiles, and other characters |
ISO/IEC 10779: 2008 |
Information technology – Office equipment accessibility guidelines for elderly persons and persons with disabilities |
ISO/IEC 11694‑3:2008 |
Identification cards – Optical memory cards – Linear recording method – Part 3: Optical properties and characteristics |
ISO/IEC 11694‑4:2008 |
Identification cards – Optical memory cards – Linear recording method – Part 4: Logical data structures |
ISO/IEC 11770‑2:2008 |
Information technology – Security techniques – Key management – Part 2: Mechanisms using symmetric techniques |
ISO/IEC 11770‑3:2008 |
Information technology – Security techniques – Key management – Part 3: Mechanisms using asymmetric techniques |
ISO/IEC 14443‑1:2008 |
Identification cards – Contactless integrated circuit cards – Proximity cards – Part 1: Physical characteristics |
ISO/IEC 14443‑4:2008 |
Identification cards – Contactless integrated circuit cards – Proximity cards – Part 4: Transmission protocol |
ISO/IEC 14496‑15:2004/ Amd 2:2008 |
Information technology – Coding of audio- visual objects – Part 15: Advanced Video Coding (AVC) file format – Amendment 2: File format support for Scalable Video Coding (SVC) |
ISO/IEC 14496‑16:2006/ Amd 1:2007/Cor 1:2008 |
Information technology – Coding of audio- visual objects – Part 16: Animation Framework eXtension (AFX) – Amendment 1: Geometry and shadow – Technical Corrigendum 1 |
ISO/IEC 14496‑3:2005/ Amd 9:2008 |
Information technology – Coding of audio- visual objects – Part 3: Audio – Amendment 9: Enhanced low delay AAC |
ISO/IEC 14496‑4:2004/ Amd 19:2007/ Cor 1:2008 |
Information technology – Coding of audio- visual objects – Part 4: Conformance testing – Amendment 19: Audio lossless coding (ALS) – Technical Corrigendum 1 |
ISO/IEC 14496‑4:2004/ Amd 11:2006/ Cor 3:2008 |
Information technology – Coding of audio- visual objects – Part 4: Conformance testing – Amendment 11: Parametric stereo conformance – Technical Corrigendum 3 |
ISO/IEC 14496‑4:2004/ Amd 29:2008 |
Information technology – Coding of audio- visual objects – Part 4: Conformance testing – Amendment 29: Symbolic Music Representation conformance |
ISO/IEC 14496‑5:2001/ Amd 10:2007/ Cor 2:2008 |
Information technology – Coding of audio- visual objects – Part 5: Reference software – Amendment 10: SSC, DST, ALS and SLS reference software |
